Masking Stamped Images: Cutting Masks, Layered Scenes, Mortise Masks
On the table
- Low-tack masking paper, 8.5 x 11 inch sheets
- Sticky notes for small masks
- Fine-tipped scissors and a craft knife with a fresh blade
- Glass cutting mat
- Black dye or hybrid ink
- Smooth white cardstock, 100–110 lb
- Stamp positioning tool (optional, helps line masks up)
- Blending brush and a pale blue ink for skies
Picture a small scene on a 4 x 5.25 inch panel: a fox in front of two pine trees, a low hill line and a pale sky. Stamped straight, the tree trunks run right through the fox. Masked, the fox sits in front and the trees disappear behind it, the way they would in a drawing. Covering what is already stamped before stamping what belongs behind it is all masking is, and it turns a handful of stamps from the rubber stamping shelf into a landscape.
A mask in five minutes
- Stamp the front image, the fox, on your card panel.
- Stamp it again on masking paper, or across the sticky strip of a sticky note.
- Cut the copy out on the line or a hair inside it. A cut outside the line leaves a white halo around the finished image.
- Lay the mask exactly over the stamped fox and press it down.
- Stamp a tree so it overlaps the masked area, then peel the mask away.
The tree now stops at the fox’s outline. Repeat for the second tree.
Cutting is the slow part. Fine-tipped scissors handle outer curves; a craft knife on a glass mat is quicker for inside corners and the gaps between legs. Thin parts such as whiskers or the tip of a tail can stay unmasked if they are too fine to cut, since a few crossing tree lines rarely show once the scene is colored.
Mask paper comes in sheets with low-tack adhesive on the back. Sticky notes work for small images if you stamp across the adhesive strip. Anything larger than the strip needs proper mask paper, or a dot of removable adhesive to stop it lifting.
Building a scene from front to back
Stamp the element nearest the viewer first and work toward the horizon.
- Foreground figure: stamp, then mask.
- Midground trees, fence or house: stamp each one, masking as you go where they overlap each other.
- Ground line: cut a strip of mask paper with a gently curved top edge and lay it over the lower part of the panel, leaving the figure masks in place.
- Background: stamp distant hills or clouds, then blend the sky down to the ground mask.
- Remove every mask at once.
Resist peeling masks off between steps unless something needs coloring in between. Each mask lifted and laid back is another chance for it to shift by a sixteenth of an inch, and that shift shows as a sliver of white or a doubled line.
A positioning tool makes layered scenes far easier. The panel stays put in the tool while masks go on and come off, and the stamp lands where you set it the first time, so a pale tree can be stamped again with its mask undisturbed. Setup details are in the stamp positioning tool guide. The same tool makes perfect masks: stamp the image on the panel, slide a piece of mask paper into the same corner, and stamp again. The copy matches the original exactly.
Mortise masks
Cutting out a mask leaves two pieces: the image and the sheet it came from, now with an image-shaped hole. That leftover sheet is a mortise mask, and it does the opposite job. Laid over the panel, it covers everything except the opening.
- Color or blend inside one shape only. Lay a mortise mask over a stamped circle frame and blend a sunset inside the circle while the rest of the card stays white.
- Put one image inside another. Stamp a frame, cover its surroundings with the matching mortise mask, then stamp a landscape across the opening. The landscape shows only inside the frame.
- Use die-cut leftovers. The negative from a die-cut circle or stitched rectangle is a ready-made mortise mask for a framed window with ink blending inside.
A clean edge needs the mortise mask pressed down firmly around its opening. Run a fingernail along the cut edge, and blend from the mask toward the opening, never the other way, so the tool does not push ink under the edge.
Masks with blending, stencils and color
Masks and ink blending go hand in hand. A curved strip of mask paper over the lower half of a panel gives a hill line: blend blue from the top edge down to just past the mask edge, lift the mask, and the hill has a crisp top under a soft sky. Gradients and tool choice are in the ink blending guide. A stencil is really a reusable mask cut from plastic, and the registration habits from stenciling carry straight over.
Plan the coloring around the masks too. Color the foreground figure before it gets masked for sky blending, or after every mask is off. Alcohol marker ink stays wet long enough to creep under a mask edge, so give a colored area a full minute before laying mask paper across it.
Questions crafters ask
Can I reuse a mask?
Yes. Masking paper keeps enough tack for several uses if you put it back on its liner between projects. Write the stamp set name on the back so it is easy to find.
Why is there a white gap between my two images?
The mask was cut outside the stamped line. Cut on the line or a hair inside it, so the second image runs right up to the first.
Will masking paper tear my cardstock?
Low-tack mask paper should lift cleanly from smooth cardstock. For soft or delicate paper, pat a fresh mask against your palm or a cotton shirt a few times to reduce the tack before use.
What is the difference between a mask and a mortise mask?
A regular mask covers the image so stamping happens around it. A mortise mask is the leftover sheet with the image cut out of it, which covers everything except the image.
More in Rubber Stamping for Beginners: Techniques for Crisp Impressions, Inks, Masks and Embossing