Stenciling With Paste, Blended Ink and Spray, Plus Clean Registration
On the table
- Plastic stencils, 6 x 6 inch, one open design and one fine design
- Blending brushes or foam blending tools, about 1 inch
- Dye and pigment ink pads
- Spray ink in a fine-mist bottle
- Repositionable spray adhesive
- Low-tack painter's tape
- Palette knife
- Scrap paper or a craft sheet to catch overspray
The same stencil gives a completely different print depending on what goes through it. Choose the medium first, then the tool, because the medium decides the edge quality, the drying time and how much cleanup is waiting afterward.
| Medium | Result | Apply with | Cleanup |
|---|---|---|---|
| Texture or modeling paste | Raised, opaque, can be inked later | Palette knife | Into water before it dries |
| Gesso | White, slightly raised, matte | Palette knife or sponge | Water, right away |
| Dye ink | Soft, see-through gradient | Blending brush or foam | Baby wipe; staining is normal |
| Pigment ink | Opaque, shows on dark paper | Blending brush, dauber | Wipe; dries slowly, so blot |
| Spray ink | Speckled, uneven, drips and pools | Mist bottle | Rinse |
| Acrylic paint | Solid, flat color | Makeup sponge, stencil brush | Soap and water |
For a card front, blended dye ink gives the cleanest result. On a journal page or a canvas, paste and spray carry more weight, and both are messier in a way that suits the surface. Where stenciling sits among the other layers of a page is laid out in the mixed media section.
Edges that bleed, and how to stop it
A smudged outline almost always comes from one of three things: too much medium on the tool, a sideways push, or a stencil that is not touching the paper.
Too much medium. Load a blending brush, then tap it on scrap paper until it leaves a faint mark. Build color in several light passes over the stencil. Each pass deepens the shade without flooding the openings.
Sideways motion. Work in small circles that start on the plastic and move into the openings, or dab straight down. Sweeping across a fine stencil drives ink under every edge.
A lifting stencil. Thin plastic curls after a few washings, and it rides up on any texture already on the page. A light mist of repositionable spray adhesive on the back makes the stencil cling like a static sticker and peel off again cleanly. Spray it outdoors or inside a cardboard box, let it get tacky for a minute, and it holds for dozens of uses. Over raised paste, press the stencil down with your free hand right next to the area you are inking.
Spray ink is its own problem. Mist from about 12 inches away so the droplets land small, hold the stencil flat with your fingers, then lift and blot the wet pools with a paper towel if they are bigger than you want. Overspray drifts well past the stencil edge, so cover the rest of the piece. The masking guide shows how to protect an area with sticky-back mask paper, and the same masks block spray.
Lining up two-step and layered stencils
Layered stencils split one image into two to four sheets, each carrying one color. They only look right when every layer lands in the same position.
- Check the stencils for registration marks, small holes or corner notches that line up across the set.
- Tape the first stencil in place, pencil through the registration holes or along two corners, then ink it.
- Lift it and wait until the ink is dry to the touch. Pigment ink needs longer, or a quick pass of the heat tool.
- Lay the second stencil over the pencil marks and tape it down before adding the next color.
- Work from the lightest color to the darkest, so each layer covers any small misalignment in the one before it.
- Erase the pencil marks once the last layer is completely dry.
A magnetic platform, the kind sold for stamping, makes this easier: magnets pin the paper and the stencil, and nothing shifts between layers. How those platforms hold a panel square is shown in the page on stamping platforms.
Mixing stencil methods on one piece
A stencil never has to be used one way per project. A typical mixed media layer might start with paste through a large background stencil, followed by ink blended through a smaller pattern over part of it once the paste is dry, and finish with spray through a third stencil at one edge. The gesso and texture paste guide explains how long the paste needs before anything can go over it.
The cutout piece left over when a stencil is made, the mask, is the reverse image. Lay it down, blend ink around it, and the shape stays white against color. Some stencils are sold with their masks; with a homemade stencil, keep the cutout.
Partial stenciling is worth trying on cards in particular. Ink only one corner of the pattern, fading out toward the center, and the design reads as a background texture without competing with a stamped greeting.
Cleaning and storing stencils
Paste and gesso go into a tray of water the moment the stencil comes off the page. Acrylic dries into a film that bonds to plastic, and a stencil left on the table for half an hour may never come fully clean.
Ink is less urgent. Wipe the stencil with a baby wipe or stamp cleaner on a craft sheet, both sides. Color left on the plastic after cleaning is staining, and it does not transfer to the next project.
Dry stencils flat on a towel, then store them flat as well: in a binder with page protectors, in a file folder, or hanging from binder rings. A stencil that sits bent in a drawer keeps the curve and lifts at the edges every time it is used.
Before you clean an inky stencil, press it face down onto a clean sheet of paper and rub the back with your palm. The ghost print it leaves is softer than the original, and that sheet is often the background for the next card or journal page.
Questions crafters ask
What stencil thickness should I buy?
Most craft stencils are thin plastic of a few thousandths of an inch, which is right for ink and spray. A thicker stencil gives taller paste and survives more scrubbing, but very fine cutouts are only possible in thin material.
Why do my stenciled edges look fuzzy?
The brush or sponge was too wet, or it was moved sideways and pushed ink under the plastic. Offload the tool on scrap paper and apply color in small circles or straight dabs.
Can I cut my own stencils?
Yes. An electronic cutting machine cuts stencil film or heavy acetate from a simple file, and a craft knife works for bold shapes. Leave bridges between openings so the center pieces do not fall out.
How do I get dried paste off a stencil?
Soak it in warm water for ten minutes, then rub the paste off with your fingers or a soft brush. Scraping with anything hard bends fine detail.
More in Mixed Media Art Techniques for Beginners, From the Gesso Ground to Distressed Edges