Gesso and Texture Paste: Priming Surfaces and Building Raised Texture
On the table
- White gesso, 8 oz jar
- Clear gesso (for priming over print)
- Modeling paste, plus light modeling paste for pages that bend
- Palette knife with a 3 inch blade, or an old gift card
- Low-tack painter's tape, 1 inch
- Plastic stencils with open, chunky designs
- Sanding block or sandpaper, 220 grit
- Heat tool
- Baby wipes and a water tray for cleanup
Five products sit side by side on the shelf and look almost identical in the jar. They do different jobs, and picking the wrong one is the usual reason a page turns out slick, gritty or cracked. All of them belong to the first two layers of a mixed media piece, before collage or color.
| Product | What is in it | How it dries | Use it for |
|---|---|---|---|
| White gesso | Acrylic binder, chalk, white pigment | Matte, slightly rough, opaque | Priming paper, chipboard, wood; covering printed pages |
| Clear gesso | Binder and chalk, no white pigment | Translucent, gritty | Giving tooth to a surface you still want to see through |
| Black gesso | Binder, chalk, black pigment | Matte black | Dark grounds for white ink, metallics and pastels |
| Modeling paste | Acrylic with a heavy mineral filler | Hard, opaque, sandable | Raised stencil patterns, carving, sculpted edges |
| Light modeling paste | Acrylic with a lightweight filler | Soft, matte, somewhat flexible | Thick texture on pages and book covers that bend |
Texture paste is the catch-all label crafters use for the last two, and brands sell their own versions under names like structure paste or embossing paste. Read the jar for two words: heavy or light.
How much gesso each surface needs
Gesso has one main job, which is to give the next layer something to hold. How many coats that takes depends on what is underneath.
Paper. One thin coat, scraped on with a card or brushed out with a flat brush. Thick gesso on thin paper makes it ripple as it dries. Tape the sheet down on all four sides first, or coat the back too, so both sides pull the same way.
Book pages and magazine pages. Clear gesso if the print should stay visible as a background; white gesso brushed thin if it should only ghost through. Glossy magazine paper needs a light sanding first or the gesso peels off in strips once dry.
Chipboard and grayboard. Two coats. The first one soaks in and raises the surface fibers; sand lightly when dry, then add the second for a smooth face.
Wood. Sand with 220 grit, wipe off the dust with a damp cloth, then one or two coats. Raw wood drinks the first coat fast.
Metal and plastic. Gesso alone does not hold well on smooth, nonporous surfaces. The altered art guide covers degreasing, scuffing and priming tins and boxes before any gesso goes on.
A coat that looks streaky is fine. The brush or card ridges show through later ink washes as a faint grain, and plenty of artists leave them on purpose.
Spreading paste through a stencil
- Tape the stencil down on two opposite edges with low-tack tape. Paste is heavy and drags a loose stencil sideways.
- Load the palette knife with about a teaspoon of paste. More than that ends up pushed under the stencil edges.
- Hold the knife at a low angle and spread across the stencil in one direction, then scrape back once to take off the excess. The surface of the paste should sit level with the top of the plastic.
- Lift the stencil straight up in one move. Sliding it off smears the edges of every opening.
- Drop the stencil into a tray of water right away. Dried paste is far harder to remove than wet paste.
- Leave the piece flat to dry.
One pass gives a raised layer about as tall as the stencil is thick. For higher texture, let the first layer dry and stencil over it again in the same position, which only works if the stencil can go back exactly where it was. Pencil a mark at two corners before lifting it the first time.
To color the paste itself, stir a drop of acrylic paint or ink reinker into a small amount on a palette before spreading. Tinted paste dries lighter than it looks wet. The stenciling guide compares paste with ink and spray through the same stencil.
Drying without cracks or bubbles
A single stencil-height layer of modeling paste air dries in a couple of hours, depending on the room. Anything thicker, roughly 1/8 inch and up, needs overnight.
Heat tools are tempting and risky here. The surface skins over first, the paste underneath keeps moving, and the result is small bubbles, a puffed texture or hairline cracks across the top. If you use one, keep it on a low setting, hold it farther away than you would for ink, and keep it moving. Stop as soon as the surface goes from shiny to matte, then let the rest dry on its own.
Cracks that show up days later have a different cause: the substrate bent. Heavy modeling paste dries hard, and a journal page or a book cover flexes every time it is opened. Light modeling paste or a layer of soft gel medium mixed into the paste copes with that much better.
Crackle paste is the exception that wants all of the above to go wrong. Spread it thick, let it dry slowly, and it splits into a pattern of fine fissures, which a rub of dark ink later picks out like old paint.
Sanding, carving and inking dried paste
Dried modeling paste takes a sanding block well. A few strokes with 220 grit knock the sharp peaks off a stencil pattern and give it a worn, stone-like face. For lines and lettering, scratch into the paste with a wooden skewer while it is still soft, about ten minutes after spreading.
Ink is where white paste earns its place. Swipe an ink pad or a blending brush lightly across the dried pattern, and the color catches on the raised edges first while the low areas stay pale. The same motion is covered step by step in ink blending. For more contrast, ink the whole area, then wipe the tops of the pattern with a baby wipe straight away so only the recesses keep the color.
Questions crafters ask
Can I use white acrylic paint instead of gesso?
On paper it works in a pinch, but the surface stays smoother and some inks bead on it. Gesso dries matte and slightly rough, which is what lets ink, pencil and paste grip.
How long should gesso dry before the next layer?
A thin coat is dry to the touch in about 30 minutes. Give it longer in a humid room, and wait until a second coat feels room temperature, not cool, before painting or stamping.
Why did my texture paste crack?
Either it went on too thick and dried too fast, often under a heat tool, or it sits on paper that bends. Thin it to one stencil-height pass, let it air dry, and use light modeling paste on journal pages.
Can I put texture paste on a card that goes in the mail?
Yes, in a thin layer. A card with raised paste is no longer flat letter mail, so it may need extra postage, and the paste should be fully dry before it goes into the envelope.
More in Mixed Media Art Techniques for Beginners, From the Gesso Ground to Distressed Edges