Clean and Simple Cards: White Space, One Focal Point, Rule of Thirds
On the table
- Smooth white cardstock, 110 lb, for bases and panels
- One accent cardstock in a strong color
- Paper trimmer and a ruler with 1/16 inch markings
- Stamp positioning tool or acrylic block
- Black dye ink and one colored ink
- Foam adhesive squares, 1/16 inch
- Pencil with a hard lead (2H) and an eraser
The usual trouble with a clean and simple card is that it looks unfinished. A stamped flower floats near the middle of a white panel, the greeting sits a little too close to it, and a strip of empty card along one side looks like something fell off. Nothing on that card is wrong on its own. It just shows no decisions.
A busy card hides its choices under layers. A CAS card shows every one, so each gap has to look chosen.
Why an empty card and a clean card look different
Three things separate the two, and none of them is the number of elements.
The first is placement. An element placed off center, on a line that can be measured, looks deliberate. An element placed roughly in the middle looks like a default.
The second is edges. A panel trimmed 1/32 inch out of square is invisible on a layered card and obvious on a white one, because the eye compares it with the card edge right next to it.
The third is visual weight. A dark, solid image pulls hard; a thin outline image pulls gently. Two heavy things on one small front fight, and one heavy thing with nothing to balance it tips the card to one side.
Placing the focal point on the thirds
Divide the card front into thirds in both directions and put the focal image on one of the four points where the lines cross. The greeting then goes on the diagonal opposite, or along one of the thirds lines, so the two balance across the card. The measurements are awkward fractions, which is exactly why most crafters guess and land in the middle.
| Card front | Vertical lines, from the left | Horizontal lines, from the top |
|---|---|---|
| A2 portrait, 4.25 x 5.5 in | about 1 7/16 and 2 13/16 in | about 1 13/16 and 3 11/16 in |
| A2 landscape, 5.5 x 4.25 in | about 1 13/16 and 3 11/16 in | about 1 7/16 and 2 13/16 in |
| Square, 5.5 x 5.5 in | about 1 13/16 and 3 11/16 in | about 1 13/16 and 3 11/16 in |
| 5 x 7 in portrait | about 1 11/16 and 3 5/16 in | about 2 5/16 and 4 11/16 in |
Mark the points with tiny pencil dots on the very edge of the card, where an eraser will take them off later. A stamp positioning tool makes the rest easy: line the panel up against the corner, place the stamp over the dot, and if the impression comes out pale, ink again and stamp in exactly the same spot.
Margins that read as intentional
Keep the side margins equal and the bottom margin slightly larger than the top. Picture framers weight the bottom of a mat for the same reason: the optical center of a rectangle sits a little above the measured one, so a design centered by ruler looks like it is sliding down. On an A2 front with a single panel, 3/8 inch at the sides and top with 1/2 inch at the bottom looks settled.
Spacing between elements follows a simple rule. Things close together read as a group, and things far apart read as separate. A greeting placed within about 1/4 inch of the image belongs to it. A greeting placed an inch away is its own element. Somewhere around 5/8 inch the eye cannot decide, and that is where most crooked-looking cards sit.
Three elements, then stop
A CAS card works with three things: the focal image, the greeting and one small accent. The accent might be a group of three enamel dots, a 1/4 inch strip of the accent cardstock, or a short line of stitching drawn with a fine pen. Put a fourth element on and the white space starts to look like leftover space.
Color follows the same restraint. Black for the greeting, one accent color for the image, and that accent color repeated once more somewhere else on the card, in the dots or the strip. Repetition is what ties a sparse card together; a second accent color usually breaks it apart.
Where the depth goes
If one element sits on foam squares, make it the focal image, and only that. The greeting stays flat. A heat embossed greeting gives texture and shine with no bulk at all, and black embossing powder on bright white cardstock is about as crisp as a sentiment gets; the heat embossing guide covers the powder and the static problems.
A card with no foam at all can still have depth. Stamp the image once in a pale ink, shift it 1/16 inch down and to the right in the positioning tool, and stamp again in the darker ink. The pale layer reads as a shadow.
Rescuing a CAS card that went wrong
White space forgives nothing, but most mistakes can still be saved without starting over.
- Crooked greeting. Trim the whole panel 1/8 inch smaller on each side, re-square it against the trimmer, and mount it on a mat in the accent color. The new edges give the eye a straight line to compare with, and the slant shrinks visually.
- Ink smudge on the white. If it falls near a thirds line, cover it with the accent: a dot, a sequin, a tiny stamped leaf. If it falls anywhere else, trim it away and use the remaining panel.
- Image too close to the middle. Trim the panel off center so the image lands on a thirds line of the new, smaller panel, then mount that panel off center on the card base.
- Card feels bare even though everything is placed correctly. Add the 1/4 inch accent strip along the lower thirds line, running off both edges of the card.
The sparse look also borrows well from layout diagrams; a few card sketches with only two or three blocks translate straight into clean and simple fronts. The card making basics cover bases and matting if the panel sizes above are new.
Before calling a CAS card finished, prop it on a shelf and look at it from across the room. At six feet a misplaced greeting is obvious, and so is a margin that is 1/16 inch narrower on one side.
Questions crafters ask
What does CAS stand for in card making?
Clean and simple: a card with generous white space, a single focal point and very few layers. A one-layer card, where everything is stamped straight onto the base, is the strictest form.
Should the focal image sit in the middle of a CAS card?
Usually not. Dead center reads as static on a small card. Put the image where two thirds lines cross, about 1 7/16 inches in and 1 13/16 inches down on an A2 portrait front, and let the greeting balance it on the opposite side.
How close should the greeting be to the image?
Either close enough to belong to it, within about 1/4 inch, or clearly apart, an inch or more. Anything in between looks like a placement mistake.
Can a clean and simple card have patterned paper?
Yes, as one small strip or a single die cut. Once patterned paper covers more than a narrow band, the white space stops doing its job and the card turns into a layered design.
More in Card Making Techniques and Ideas for Beginners, From the First Fold to Pop-Up Cards