Fun Fold Cards: Sizes and Score Lines for Gatefold, Easel and Z-Fold
On the table
- Cardstock, 8.5 x 11 inch, 100–110 lb, for gatefold, Z-fold and easel bases
- Cardstock, 12 x 12 inch, 80 lb, for tri-folds
- Scoring board with 1/8 inch grooves
- Paper trimmer
- Bone folder
- Patterned paper pad, 6 x 6 inch
- Foam adhesive squares for the easel stopper
- Ribbon or a 1 inch strip of cardstock for a belly band
- A2 envelopes
A fun fold changes how a card opens without changing the envelope it goes in. Here are the measurements first, since they are what gets looked up at the trimmer:
| Fold | Cut the cardstock | Score at | Folds to |
|---|---|---|---|
| Gatefold, landscape | 11 x 4.25 in | 2.75 and 8.25 in on the 11 in side | 5.5 x 4.25 in |
| Gatefold, portrait | 8.5 x 5.5 in | 2.125 and 6.375 in on the 8.5 in side | 4.25 x 5.5 in |
| Z-fold | 11 x 4.25 in | 5.5 and 8.25 in on the 11 in side | 5.5 x 4.25 in |
| Easel | 11 x 4.25 in | 5.5 and 8.25 in on the 11 in side | 5.5 x 4.25 in |
| Tri-fold | 12 x 5.5 in | 4.25 and 8.5 in on the 12 in side | 4.25 x 5.5 in |
Every fold in that table closes to A2, which means the same envelopes, the same mats and the same cutting habits as a plain card. The 11 x 4.25 inch pieces come from a letter sheet cut in half lengthwise; the tri-fold needs a 12 x 12 sheet, which gives two 12 x 5.5 strips and a 1 inch offcut for a belly band.
Fold direction is where most fun folds go wrong, so mark each score lightly in pencil as “M” for mountain or “V” for valley before folding anything.
Grain and weight before anything else
Cardstock has a grain, the direction most of its fibers lie. A fold along the grain is crisp; a fold across it resists and often cracks, showing white on dark stock. To find it, bend a sheet gently one way and then the other without creasing. The direction that bends with less resistance is with the grain.
A plain card has one fold, so grain rarely matters. A Z-fold has two and a tri-fold folds three layers into one, so cut those pieces with the grain running parallel to the score lines. Weight matters for the same reason: 110 lb stock is right for a gatefold, but a tri-fold in 110 lb springs open on the table, and 80 lb sits flat.
Gatefold: centering the closure
The two flaps of a gatefold meet in the middle of the card, so any gap or overlap between them is the first thing anyone sees. Measure the strip before scoring. A strip that came off the trimmer at 10 15/16 inches leaves a 1/16 inch gap between the closed flaps, and one that is not square leaves a gap shaped like a wedge. Trim it to exactly 11 inches with square corners, then score both lines from the same edge.
Decorate the flaps as one design and then cut it. Mount a 5.25 x 4 inch panel across both closed flaps, then run a craft knife down the gap between them. The pattern lines up perfectly when the card is shut.
To keep it closed, either slide on a belly band or mount the focal element, on foam, to the right flap only, letting it overlap the left. The second option means no loose part to lose.
Easel: where the stopper goes
Fold the easel card at 5.5 inches as a normal card, then fold the front half back on itself at 8.25 inches. Glue the decorated front panel, about 5.25 x 4 inches, to the outer quarter only: the section between the 8.25 inch score and the end of the strip. Glue it lower and the easel cannot fold.
Open the card, let the front lean back, and look where its folded edge lands on the inside base. That is where the stopper goes. Stick a scrap there first and test, because the right spot moves with the weight of the front panel. A greeting strip on two layers of foam squares makes a stopper that also carries the message.
Z-fold and tri-fold: thickness and clearance
The Z-fold shows its back panel on one side and a stepped half-panel on the other, so decorate the inside back panel as carefully as the front; it is visible on the closed card. Embossed backgrounds look especially good on the stepped panel. Run the paper through the embossing folder before scoring, since the pressure of a folder flattens a score line made earlier.
The tri-fold measurements leave the last panel 3.5 inches wide, 3/4 inch narrower than the other two. That panel folds in first, and the narrower width gives it room to sit inside without buckling the outer fold. Decorate it with flat layers only; a die cut on foam on the inner panel pushes the card open.
Both cards carry three layers of cardstock in the envelope. Add patterned paper and a mat to each panel and a Z-fold can reach the thickness of a card with foam squares, so weigh and measure one before mailing a batch.
Stepper cards, for later
A stepper folds the front of the card back on itself in narrowing steps, so that when the card stands open, tiers rise one behind another, each carrying a small panel or greeting. Published stepper patterns differ in their step widths and score positions, and the folds interact: change one measurement and the others shift. Draw the stepper full size on copy paper and fold the paper model before cutting cardstock.
It is the hardest fold in this group to get square, and the one where scoring from a single reference edge matters most.
Folds that carry over to other projects
The Z-fold is the same accordion that holds pages in mini albums, and a long Z-fold strip with several panels turns into a small album that stands on a shelf. Gatefold and Z-fold panels also take a small box step from the pop-up card guide if the card needs a surprise on the inside. Bases, matting and adhesives for every card shape are in the card making section.
On any multi-fold card, burnish each fold once after scoring and again after the card is fully decorated: the extra layers lift the folds slightly, and a second pass with the bone folder pulls the card flat for the envelope.
Questions crafters ask
Do fun fold cards fit a normal envelope?
The gatefold, Z-fold, easel and tri-fold measurements here all close to 4.25 x 5.5 or 5.5 x 4.25 inches, so they go into A2 envelopes. Check the thickness of tri-folds and decorated easels, which carry more layers than a plain card.
Why does my fold crack along the score?
The fold probably runs against the grain of the cardstock, or the stock is too heavy for a card with several folds. Turn the sheet so the folds run with the grain, or drop to 80 lb for tri-folds.
How do I keep a gatefold card closed?
Slide a belly band of ribbon or a 1 inch cardstock strip around it, or attach the focal element to one flap only so it overlaps the other and holds it.
What holds an easel card up?
A stopper: a sentiment strip, button or die cut mounted on foam inside the card. The bottom edge of the folded front rests against it.
More in Card Making Techniques and Ideas for Beginners, From the First Fold to Pop-Up Cards