My Creative
Classroom

How to Make Shaker Cards: Acetate Window, Foam Frame and Fillers

Card Making Level: First project Published Updated

On the table

  • Cardstock, 100–110 lb, for the card base and a 4 x 5.25 inch window panel
  • Acetate or transparency sheet, cut 1/2 inch larger than the window
  • Double-sided foam tape, 1/8 inch thick and 1/4 inch wide
  • Strong double-sided tape, 1/8 inch wide, for the acetate
  • Sequins, seed beads or paper confetti, about a teaspoon per card
  • Window die and die cutting machine, or a craft knife and metal ruler
  • Anti-static pouch or a dryer sheet
  • A second panel of cardstock, 4 x 5.25 inches, for the back of the shaker

A shaker card is a small sealed box: a window of acetate in front, a frame of foam tape for walls, a panel of cardstock at the back, and a spoonful of sequins loose inside. Tip the card and the filler slides across the window. Everything that goes wrong with a shaker comes down to that box having a gap somewhere, or to the filler sticking to the acetate instead of moving.

Build the first one on an A2 card with a plain rectangle or circle window. Shaped windows come later.

Picking a filler before cutting anything

The filler decides how the card behaves, so choose it first. Some move freely, some cling, and some are so heavy that they slide only when the card is held flat.

Filler How it moves Watch out for
Flat sequins, 4–6 mm Slides and flips, catches light Very few problems; the easiest first filler
Cupped sequins Rattles, a bit noisier Can stack up in one corner
Seed beads Rolls fast, satisfying sound Heavy; one teaspoon is plenty
Microbeads Pours like sand Clings badly to charged acetate
Paper confetti or tiny punched shapes Floats slowly Static, and it can get stuck under the foam
Loose glitter Shimmers in a cloud Coats the acetate and leaks through the smallest gap

Mix two sizes for the best movement: mostly flat sequins with a pinch of seed beads to keep them tumbling.

Building the shaker, layer by layer

  1. Cut a window panel of 4 x 5.25 inches, the usual mat size for an A2 card. Cut the window so at least 1/2 inch of cardstock remains on every side of it. The foam frame needs that room.
  2. Turn the panel face down. Run thin double-sided tape around the window, about 1/8 inch from its edge.
  3. Cut acetate 1/2 inch larger than the window in both directions, peel the protective film if it has one, and press it onto the tape. Hold it only by the edges.
  4. Rub the inside face of the acetate with the anti-static pouch or a dryer sheet.
  5. Lay foam tape around the window on top of the acetate edges, as close to the opening as possible without showing through it. Butt the strips tightly at the corners. If a corner leaves a gap, snip a small piece of foam and press it in.
  6. Check the frame from the front. Any foam visible in the window will show for the life of the card; move it now.
  7. Peel the foam liners. Pour the filler into the center of the well through a folded scrap of paper used as a funnel, keeping it off the sticky foam. Brush stray pieces off the adhesive with a soft paintbrush.
  8. Line up the back panel over the frame and lower it straight down. Press along every foam line with a bone folder.
  9. Shake the panel hard over a sheet of white paper.
  10. Mount the finished panel on the card base with a tape runner, covering the back panel fully.

If you die cut the window, a plain rectangle die in a manual die cutting machine gives cleaner corners than a craft knife.

The static problem

Static is the most common complaint about shaker cards, and it is worst in winter, when heated indoor air is dry. Acetate builds up charge whenever it is rubbed or peeled, and anything light inside the window jumps to the plastic and stays there. Confetti and microbeads suffer most; heavy seed beads barely notice.

Treat the acetate the same way you would treat cardstock before heat embossing: wipe it with an anti-static pouch, the small cloth bag of powder sold for embossing, immediately before the filler goes in. A dryer sheet works too. Do it on the inside face, because that is the surface the filler touches. Once the shaker is sealed there is no way back in, so a cling problem discovered at step 9 means taking the card apart.

A smaller trick helps with stubborn fillers: tap the filler into the well, close the shaker, then hold the panel window-side down and flick the back a few times. Anything clinging loosely lets go.

Leaks and the corner test

A leaking shaker drops sequins into the envelope, and the recipient opens a card with a half-empty window. Leaks come from three places:

  • a gap where two foam strips meet at a corner;
  • a sequin or bead caught on the foam adhesive, holding the back panel off it;
  • a back panel pressed down only in the middle, with loose edges.

The white-paper test at step 9 finds all three. Shake hard, in every direction, for a good ten seconds. A single sequin on the paper is enough reason to open the card now, while it is still a panel and not a finished card.

Variations once the basic shaker works

Once the plain rectangle stops being a challenge, the same box comes in other shapes.

Full-front shaker

Cover the whole 4 x 5.25 inch panel with acetate and put a die-cut frame or a stamped and fussy-cut outline image on top of the acetate. The foam goes under the frame, around the outer edge of the panel.

Shaped window

Circles, hearts and ornament shapes all work, but foam tape will not curve. Cut the foam frame from a sheet of adhesive foam with the next size larger die in the same shape, so the frame follows the window exactly.

Shaker under the greeting

A small window, about 1 x 3 inches, sits behind a stamped sentiment strip. It uses barely a pinch of filler and suits cards where the main image is already busy.

Shakers go down well in a set of handmade Christmas cards, though they slow a batch down more than any other technique. For more interactive folds and moving parts, the card making section has the full list.

On a card that will travel, keep to one layer of 1/8 inch foam. Two layers make a deeper well, but stacked on the card base they push the card past the 1/4 inch letter thickness at the post office.

Questions crafters ask

Why do sequins stick to the inside of the window?

Static. Peeling the protective film off acetate charges it, and light fillers cling. Rub the inside face with an anti-static pouch or a dryer sheet right before filling, and handle the acetate by its edges.

How much filler goes into a shaker card?

Enough to cover roughly a third of the floor of the well when the card lies flat, which is about a teaspoon for a 2.5 inch window. Too much and nothing moves; too little and the window looks empty when the card stands.

Can I use liquid glue on acetate?

Avoid it. Liquid glue stays visible through the clear sheet and grips poorly on the slick surface. Use thin double-sided tape on the cardstock around the window and press the acetate onto it.

Can a shaker card go through the mail?

Yes, if the finished card stays under 1/4 inch thick, which one layer of 1/8 inch foam allows. The USPS may charge the nonmachinable surcharge for a card that is rigid or uneven, so weigh and check one before mailing a stack.

More in Card Making Techniques and Ideas for Beginners, From the First Fold to Pop-Up Cards