My Creative
Classroom

Manual Die Cutting Machines: Opening Widths, Steel-Rule and Thin Dies

Die Cutting Level: First project Published

On the table

  • Manual roller machine with a 6 inch or wider opening
  • Platform or spacer plate for thin dies
  • Two clear cutting plates
  • Thin etched dies, a nested rectangle or circle set
  • One steel-rule die for multi-layer cuts (optional)
  • Cardstock, 65–110 lb
  • Low-tack tape

Turn the handle on a manual machine and two steel rollers pull a stack of plates through the gap between them. The pressure inside that stack is far beyond what a hand could manage, and it is the only thing doing the cutting. Nothing about a manual machine needs setting: no blade depth, no material preset, no file. What separates one machine from the next is how wide a stack it accepts, how thick, and how evenly the rollers press from one edge to the other.

Opening width decides what the machine is for

The opening is the width of the slot the plates feed into. It sets the largest die, folder or sheet the machine can take, and that, more than any feature on the box, decides whether it suits cards, scrapbook pages or both.

Opening width What fits Typical work
Under 3 in Small dies and tag-size pieces Sentiment strips, tags, small accents
About 6 in An A2 panel (4.25 x 5.5 in) and most A2 embossing folders Card making; the Sizzix Big Shot is the familiar example
About 8.5 to 9 in 5 x 7 in panels and larger background dies Bigger cards, half-letter pieces, wide folders
About 12 to 13 in Sheets up to 12 in wide Scrapbook borders, large steel-rule dies

For a card maker the 6-inch class is the sensible middle. Dies sold for cards are sized around the A2 panel, embossing folders for cards are a little larger than it, and a machine of that class fits on a shelf when it is not in use. The narrow travel machines suit someone who mostly cuts small shapes away from home; on a full card front they run out of room fast.

Weight is the other half of the decision. A heavier machine stays put while you crank it. Lighter models usually have suction feet, and those only grip a smooth, clean surface, so a wooden table with a rough finish lets the machine walk an inch or two on every pass.

Steel-rule dies and thin dies are different tools

Both kinds go through the same rollers, and both are called dies, but they behave so differently that it helps to think of them as separate tools.

Steel-rule dies

A steel-rule die is a strip of sharpened steel bent into a shape and set upright in a block of wood or dense foam, with springy foam around the blade that pushes the cut piece back out. The blade is tall and sturdy. It cuts chipboard, felt, craft foam, thin fabric and several sheets of cardstock in a single pass, which makes it the tool for repeated basic shapes: tags, flowers, banners, box templates. Because the die itself is thick, the stack around it is thin, often just the die, the material and one plate.

Thin etched dies

Thin dies are chemically etched from a sheet of metal not much thicker than a credit card. The etching process allows fine detail that a bent steel strip could never follow: lace edges, script words, stitched outlines, tiny leaves. They cut one or two layers of cardstock well and paper easily, and they struggle with anything denser. Most need a platform or spacer below the plates to bring the stack up to height.

Thin dies come in a few recognizable forms. Nested sets give the same shape in graduated sizes, so one set makes a panel and its mat. Coordinating dies match the outline of a stamp in a stamp set and cut around the stamped image. Open-frame dies have hollow centers, which lets you see exactly where the cut lands on a stamped piece. Nested frame dies are also the quickest way to cut both the window and the foam frame for shaker cards, since two neighboring sizes give the opening and the border in one pass each.

Steel-rule die Thin etched die
Cuts Chipboard, felt, foam, fabric, stacks of cardstock One or two layers of cardstock, paper, vellum
Detail Simple outlines Fine lines, script, lace
Stack Thin (the die fills the height) Platform plus two plates
Storage Bulky, shelf or bin Flat, on magnetic sheets

Running a stack through

The exact order of platform and plates changes from machine to machine, so keep the chart from the manual or the platform somewhere you can see it. The general sequence for a thin die looks like this:

  1. Lay the platform and the first cutting plate down in the order the chart gives.
  2. Place the die with its cutting edge facing up, then lay the cardstock over it. Hold the die to the paper with a small piece of low-tack tape at two opposite corners.
  3. Put the second plate on top and line the stack up square with the opening.
  4. Turn the crank at an even speed until the stack comes out the far side. A jerky, stop-start crank gives an untaped die more chances to shift.
  5. Before lifting the top plate, peel back one corner of the cardstock and look. If the outline is pressed but not cut through, put the corner back down and run the stack through in the opposite direction.

Step 5 saves more panels than any other habit, because once the die has moved there is no lining it up again. When a reversed pass still leaves the cut incomplete, the stack needs more pressure, and the guide to cutting plate sandwiches shows how to add it with shims without cracking a plate.

Keeping the machine in working order

A manual machine asks for very little. Wipe paper dust and glitter off the rollers with a dry cloth now and then, because grit pressed into a plate prints as a dent in every later cut. Keep the platform folded and the plates stored flat beside the machine. Treat a crank that suddenly feels stiff as a message about the stack, never as a reason to lean on it. Carry the machine by its body or its handle, not by the fold-out trays.

Steel-rule dies, thin dies, embossing folders and the rest of the family all live in the die cutting machines section, but for a first evening a single nested rectangle set is plenty: cut one panel from patterned paper, cut a mat from plain cardstock in the next size up, and check whether the border between them comes out even on all four sides.

Questions crafters ask

Can thin dies be used in a machine sold for steel-rule dies?

Usually, yes. Thin dies need a platform or spacer under the plates to make up the height a thick steel-rule die would fill, and most machines that take both come with one.

Why does my machine take so much force to crank?

The stack is too thick. Remove any shim, check the order against the machine's chart, and never push a stack through with your body weight or a mallet, because that is how gears and plates break.

Is a wider opening always the better buy?

Only if you regularly cut 5 x 7 inch panels or full letter sheets. Wider machines weigh more and take up more table, and a 6 inch opening already handles every A2 card panel.

More in Die Cutting Machines Guide for Beginners, From Manual Rollers to Electronic Cutters