Die Cutting Problems and Fixes: Incomplete Cuts and Stuck Pieces
On the table
- Low-tack tape or a magnetic die mat
- Wax paper, cut to plate size
- Poke tool or die pick
- Stiff die brush or an old stencil brush
- Manila folder scraps for shims
- Magnetic sheets and clear envelopes for storage
- Silica gel packets
Most failed die cuts fall into a handful of patterns, and the pattern usually names the cause. A rectangle that cuts cleanly on the left and stays attached on the right points to pressure. A lace border that cuts perfectly and then tears as you pull it free points to release. So look closely at the spoiled piece before changing anything, because the fix for one is useless for the other. The fixes below are written for the manual roller machines in the die cutting machines section, though paper choice and removal apply to electronic cutters too.
Read the symptom first
| Symptom | Likely cause | First thing to try |
|---|---|---|
| Outline pressed in, nothing cut | Stack too thin, or plates worn | Add one shim sheet under the bottom plate |
| Cut on one side, not the other | Warped or worn plate, die near the edge of the rollers | Flip the plates, center the die, run again end to end |
| Cut everywhere except fine detail | Cardstock too heavy or fibrous | Lighter, smoother cardstock and a second pass |
| Tiny inner pieces stay in the die | Normal for intricate dies | Wax paper, die brush, poke tool |
| Die cut tears coming out | Pulled off from the front | Push it out from the back of the die |
| Cut is crooked or doubled | Die shifted during the pass | Low-tack tape or a magnetic mat |
| Crank stalls partway | Stack too thick | Remove the shim, check the machine’s chart |
| Plate cracks | Too much pressure | Take shims out, replace the plate |
Incomplete cuts: start with the cheapest fix
Before lifting the top plate, peel back one corner of the paper. If the cut is not through, lay the corner flat again so nothing moves, and work up this ladder one step at a time:
- Run the stack back through in the opposite direction.
- Turn the whole stack end to end and run it through again.
- Flip the top plate, or swap the two plates, and repeat.
- Add one shim under the bottom plate.
- Try a fresh plate in place of the more worn one.
- Only then suspect the die itself, for instance a thin die with a slight bend that keeps one section off the paper.
Most cuts are finished by step 2. Steps 3 to 5 deal with plates and pressure, and the page on cutting plate sandwiches explains how to shim and rotate plates without overdoing it.
Paper choice is the quiet cause behind a lot of partial cuts. Cheap cardstock with long, loose fibers tends to leave fuzzy edges and little bridges of uncut fiber, especially at sharp inside corners. A smooth, dense stock of 65 to 80 lb cuts cleaner than heavier stock with a soft surface, even though the heavier one sounds sturdier.
Intricate dies and the wax paper trick
Dies with very fine cut lines, such as lace borders, script words and filigree corners, cut beautifully and then hold on to everything. The cardstock is pressed so firmly into the narrow spaces between the blades that it wedges there.
Wax paper loosens that grip. Lay a sheet of ordinary kitchen wax paper between the die and the cardstock, then run the stack as usual. The thin waxy layer goes through the cut with the paper, and the pieces slide out of the die far more easily afterward.
Two more things help with fine dies. Use the lightest cardstock that still suits the card, since every extra pound makes the cut lines wedge harder. And for a word that has to stay in one piece, back the cardstock with a double-sided adhesive sheet before cutting: the word comes out with its glue already in place, including the inner pieces of letters like a, e and o, and lays down exactly as it was cut.
Fine dies are fiddly and still worth owning: nothing cut by hand gets close to a lace edge.
Getting pieces out without tearing them
Never peel a delicate die cut off the front of the die. Turn the die over so the cut side faces down and push the pieces out from the back through the openings in the metal. A poke tool, a fine metal pick with a handle, reaches into the small openings; a stiff brush swept across the back of the die pushes out a whole field of tiny bits at once. Some dies have small release holes built in for exactly this.
Brush small pieces onto a sheet of scrap paper instead of the table. The dots from inside letters, the tiny leaves of a vine border and the confetti circles from a stitched frame are useful as fillers and accents, and they vanish into the carpet otherwise.
Storing dies so they stay flat and findable
Thin dies bend under weight and get lost in a drawer. The common system is a magnetic sheet: the dies cling to it and stay flat, and the sheet slides into a clear envelope, a binder sleeve or a shallow box. Store coordinating dies on the same sheet or in the same envelope as the stamp set they match, the way clear and cling stamps are usually filed by set, so the two never get separated.
Labeling saves a lot of searching. Run each die once through a scrap of cardstock and stick the cut outline onto the outside of its envelope, which shows the exact shape and size at a glance.
Moisture is the last enemy. Many thin dies are carbon steel and spot with rust if they live in a damp basement or go back into storage still wet from inking. Keep a silica gel packet in each box, wipe ink off with a dry cloth before filing a die away, and stand steel-rule dies side by side on a shelf, since a heavy pile pressing on them for months can flatten the ejection foam around the blades.
Questions crafters ask
Is it bad to run a die through the machine twice?
No. A second pass with nothing moved, or with the stack turned end to end, is the normal first fix for a cut that is almost complete, and it does no harm to the die.
Why do my dies cut plain cardstock but not glitter cardstock?
Glitter cardstock carries a hard, thick surface layer that needs more pressure. Run it twice, add one shim, and use a smaller, simpler die where you can.
Do thin dies rust?
Many are made of carbon steel and can rust in a damp room. Store them dry with a silica gel packet in the box and wipe off any moisture or ink before putting them away.
How do I keep a die from moving on a stamped image?
Tape it at two opposite corners with low-tack tape, or lay the paper on a magnetic mat that holds the die in place, and check the position once more before the top plate goes on.
More in Die Cutting Machines Guide for Beginners, From Manual Rollers to Electronic Cutters