My Creative
Classroom

Cutting Plate Sandwiches: Stack Order, Shims, Warping and Rotation

Die Cutting Level: Some practice Published

On the table

  • Platform or spacer that came with your machine
  • Two cutting plates, plus a spare
  • Embossing mat, only if your folders call for one
  • Manila folder or 65 lb cardstock scraps for shims
  • Thin metal shim sheet (optional)
  • Permanent marker for labeling plate corners

The plates, platform and die that go through a manual machine are called a sandwich, and getting the layers right is most of the skill. Start with the order.

Job Stack, bottom to top
Thin etched die Platform or spacer, cutting plate, die with cutting edge up, cardstock, cutting plate
Steel-rule die Die with blade up, cardstock, one cutting plate (often no platform)
Embossing folder Platform or spacer, cutting plate, folder with cardstock inside, cutting plate
Deep 3D folder As above, with an embossing mat in place of one plate if the folder calls for it

Those four stacks cover most of what passes through a manual machine, but read them as a pattern to recognize. The parts have different names from one brand to the next (platform, spacer, base plate, tabs, adapter), and the thicknesses differ too. Whatever the chart printed on your machine’s platform or in its manual says is the version that applies on your table.

What every stack has in common is a target thickness. The rollers sit a fixed distance apart, and the stack has to fill that gap tightly enough for the die to cut through paper while leaving room for the whole thing to roll. A stack a sheet too thin presses an outline and cuts nothing. A stack a sheet too thick fights the crank, scores the plates deeply and eventually cracks one.

Placement inside the stack matters less than people think. A thin die cuts the same with its edge facing up and the paper on top as with the paper underneath and the die face down, as long as the cutting edge faces the paper and nothing else sits between them. Face up has one practical advantage: you can see the die through the cardstock when lining it up with a stamped image, if the stock is light enough.

Why plates curve after a few weeks

The die presses into the plate above or below it on every pass, compressing one surface more than the other. After a few dozen cuts the plate bows, like a sheet of paper that has been rolled. Every plate does this under that load, the expensive ones included.

A curved plate still cuts. The trouble starts when the curve gets strong enough to lift the ends of the stack off the bed as it enters the rollers, which can make the die shift, and when one area of the plate is so worn that dies placed there stop cutting. Both problems come from the same habit: always putting the same plate on top, the same way up, with the die in the same spot.

A rotation routine that keeps them flat

  1. Mark one corner of each plate with a permanent marker, A on one plate and B on the other, so you can see at a glance how they were last used.
  2. After every pass, flip the top plate over. The next pass then bends it back toward flat.
  3. Every few passes, swap the plates so A and B take turns as the cutting surface.
  4. Turn the stack end to end now and then, so the leading edge into the rollers is not always the same one.
  5. Move the die around the plate from cut to cut, especially small dies that would otherwise wear one patch.

With that routine, plates that would have bowed badly in a month stay usable much longer, and the wear spreads into a fine, even crosshatch you can see when the plate is held up to a window.

Shims: more pressure, one sheet at a time

When a die presses a clean outline and cuts only part of it, and flipping the plates has not helped, the stack needs to be thicker. That extra layer is a shim.

The simplest shim is a sheet of cardstock or a piece of manila folder cut to the size of the plate. Thin metal shim sheets sold for die cutting do the same job and last longer. Place the shim under the bottom plate, where it spreads the extra pressure evenly over the whole stack. For a single large die that cuts everywhere except one corner, a smaller piece of paper under just that corner sometimes does the trick, but try the full shim first.

Add one layer, run the stack, check. Then decide on a second layer.

The signs of a stack that is now too tight are easy to read. The crank needs real effort, the die leaves a deep groove in the plate in a single pass, and on embossing folders the pattern starts to look crushed at the edges. Take the shim back out at that point. Forcing a stack through is the fastest way to crack a plate, and on some machines it strains the gears. And never run a steel-rule die in the stack meant for thin dies: the tall die already fills most of the gap, and adding the platform beneath it is a reliable way to split a plate.

Chipboard deserves its own word. Covers for mini albums are usually cut from chipboard, and a thin die will not cut it however many shims go in; it needs a steel-rule die with its own, thinner stack.

When a plate is finished

Plates are consumables, and keeping a spare in the drawer saves a project on the evening one gives out. Replace a plate when it has cracked, when its grooves are deep enough to catch the paper and tear small cut pieces, or when embossed panels start showing the old die lines as faint ghost patterns. Those ghost lines matter most for embossing folders, since a pristine plate is the only way to get a clean pattern on a light cardstock.

If a die still will not cut on fresh, flat plates with one shim, the problem lies elsewhere, and the troubleshooting page on incomplete cuts and stuck pieces goes through the other suspects. All the plate stacks here belong to the manual side of the die cutting machines section; electronic cutters have mats instead and none of this applies to them.

A retired plate is not useless. Keep one for running adhesive sheets, glitter cardstock and anything else that leaves residue, so the good plates stay clean for embossing.

Questions crafters ask

Do I really need to flip the plates every time?

Yes. Each pass presses the die into the same side of the top plate, and flipping it after every cut lets the next pass push the curve back the other way before it sets.

Can I mix plates from different brands?

Only if they are the same size and thickness. A plate a fraction thinner or thicker changes the whole stack, which shows up as cuts that suddenly fail or a crank that suddenly fights back.

What can I use as a shim?

A sheet of cardstock, a piece of manila folder or a thin metal shim sheet. Add one layer at a time and test, since a stack that is too tight cracks plates faster than any amount of normal use.

Why did my cutting plate crack?

Too much pressure, usually from piled-up shims or from running a steel-rule die with the stack meant for thin dies. Old plates that are deeply grooved also crack more easily along the grooves.

More in Die Cutting Machines Guide for Beginners, From Manual Rollers to Electronic Cutters