My Creative
Classroom

Pop-Up Cards: Box Pop-Ups, V-Folds and Layered Scenes That Close Flat

Card Making Level: Confident Published Updated

On the table

  • Cardstock, 65–80 lb, for the pop-up mechanism
  • Cardstock, 100–110 lb, for the outer card
  • Metal ruler with 1/16 inch markings
  • Craft knife with a fresh blade and a self-healing mat
  • Fine embossing stylus or scoring tool
  • Liquid glue with a fine tip
  • Copy paper for test models
  • Sharp pencil and a soft eraser

A pop-up card is a geometry problem hidden inside a fold. Paper only behaves when every fold line meets the spine exactly where the design says it should, and an error of 1/16 inch at one end shows up as a mechanism that leans, sticks out of the closed card or tears on the third opening. The paper engineering in Robert Sabuda’s pop-up books looks like magic. It rests on the same few mechanisms below, measured very precisely.

Start by deciding how far the card will open, because that decides the mechanism.

Which mechanism for which card

Mechanism Card opened to Good for Made by
Box pop-up (parallel fold) 90 degrees Steps and platforms that carry figures, a stage set Cutting and folding the card itself
V-fold 180 degrees, flat One tall shape rising from the center: a tree, a cake, a heart Gluing a separate folded piece across the spine
Layered pop-up 90 degrees Scenes with foreground and background Several box steps side by side, or a step cut into another step

A box pop-up viewed with the card open flat collapses into nothing, and a V-fold at 90 degrees hardly rises. Pick one opening angle per card.

The box pop-up, measured

The box pop-up is cut into an inner card that later gets glued into an outer card, so the holes never show. Make the inner card 8 x 5.25 inches, scored at 4 inches, which folds to 4 x 5.25 and fits inside a standard A2 base with 1/8 inch to spare at top and bottom and 1/4 inch at the open edge.

  1. Fold the inner card in half along its score and burnish it.
  2. With the card still folded, mark two slits perpendicular to the fold, starting at the fold. For a first model make them 1 inch long and 1 1/2 inches apart.
  3. Cut both slits through both layers with the craft knife against the metal ruler.
  4. Score a line joining the ends of the two slits. Fold the tab between the slits forward along that score, then back again, and burnish both ways.
  5. Open the card to 90 degrees. From behind, push the tab through so it reverses direction and stands out as a step.
  6. Close the card slowly and press it flat so the new folds set.

The step that pops up is exactly as tall as it is deep, and both equal the slit length. A 1 inch slit makes a 1 x 1 inch step. Keep the slits well short of the open edge of the inner card; half the panel depth is a sensible ceiling.

Glue a figure to the front face of the step only. If it is also glued to the top of the step or to the card behind it, the mechanism locks and the card will not close.

The V-fold, angled

A V-fold is a separate piece of cardstock folded in half with a glue tab along the bottom of each side.

Draw a pencil line on each side of the spine at the same angle to it, starting from a single point on the spine. About 45 degrees on each side is a comfortable first angle. Glue the tabs along those lines so the crease of the piece sits exactly on the spine and the two tab points meet at the starting point.

A rectangle folded in half and glued this way stands with its crease straight up, whatever angle you pick. The angle decides how wide the V opens: lines close to the spine make a narrow wedge, lines far from it make a wide, shallow one. Close the card after gluing and check that the top of the piece stays at least 1/4 inch inside the card edges.

The crease and the spine have to line up. A V-fold glued 1/16 inch to one side of the spine still opens, but it rises crooked and creases the card a little more with every closing.

Layered scenes

Because a longer slit makes a step that is both taller and further forward, the long steps sit nearest the viewer. That catches people out on a first scene: a big step at the front hides any shorter step directly behind it.

Place steps side by side across the card, at different lengths, instead of one behind another. A figure glued to a short rear step must rise higher than the step in front of it to be seen. A second step can be cut into the face of a first one with the same slit-and-push method; it is fiddly, and the paper between the cuts needs to stay at least 1/2 inch wide or it tears.

For repeat production, cutting the inner card on an electronic cutting machine removes most of the measuring error, as long as the file draws score lines and cut lines on separate layers.

Scoring to the nearest 1/32 inch

Most failed pop-ups were scored slightly wrong.

Measure every line from the spine, never from the previous mark. Measuring from mark to mark adds up the small errors: four measurements each 1/64 inch off put the last line 1/16 inch out. Mark with a sharp pencil, line the ruler up on both marks, and score with a fine stylus. The groove of a scoring board is 1/8 inch apart, too coarse for mechanisms, so keep the board for the outer card.

Cuts must stop exactly on their score lines. A slit that runs 1/32 inch past the score tears there after a few openings; one that stops short makes the tab fold in the wrong place.

Fold mountain folds and valley folds in their final direction before assembling anything. Then build the whole card once in copy paper. A copy-paper model costs nothing and shows every collision.

Hiding the mechanism inside an outer card

Glue the finished inner card into an A2 base of 100–110 lb cardstock. Put adhesive only on the areas of the inner card that do not move: around the edges and well away from the slits. Glue under a step and that step is fixed in place.

Line the spines up before the glue grabs. With the outer card standing open at 90 degrees, glue the inner card’s back half to the outer card’s back panel first, close the card so the front half finds its own position, then open it and press the front half down.

A pop-up suits most of the interactive folds in the card making section, and some of the fun fold cards take a small box step on their inside panel. Mail a pop-up in a padded envelope or with a piece of chipboard behind it, and write the inside message before any mechanism goes in.

Questions crafters ask

Why does my pop-up stick out of the card when it is closed?

The mechanism or the figure on it is too large for the panel. Shorten the slits or the figure until everything stays at least 1/4 inch inside the edges with the card shut, and test in copy paper first.

Why will my V-fold not close flat?

Its crease is not sitting exactly on the card's spine, or the two glue lines are at different angles. Either fault forces the paper to buckle or tear when the card shuts.

Which cardstock weight works for pop-up mechanisms?

Lighter stock, around 65 to 80 lb, for anything that folds inside the card. Heavy 110 lb stock is right for the outer card but springs back and cracks on the small folds of a mechanism.

Can an electronic cutting machine cut pop-up cards?

Yes. A Cricut or Silhouette cuts the slits and can score the fold lines with a scoring tool or wheel, which gives very consistent results. The folding and gluing are still done by hand.

More in Card Making Techniques and Ideas for Beginners, From the First Fold to Pop-Up Cards