Water-Based Markers on Stamped Images: Blending Brush Pens With Water
On the table
- Water-based dual brush markers, 2-3 shades per color
- Water brush, medium tip
- Acrylic stamp block or plastic blending palette
- Watercolor paper, 140 lb, for wet work
- Smooth heavy cardstock, 100-110 lb, for dry coloring
- Waterproof black stamping ink
- Colorless blender pen for water-based markers
- Paper towel
Water-based brush markers color like felt pens on dry paper and blend like paint once water joins in. How much water reaches the paper is the whole game. Most stamped images colored with them use one of three blending methods, and the method you pick decides the paper underneath.
Three blending methods and what each asks for
| Method | How it works | Paper | Finished look |
|---|---|---|---|
| Palette and water brush | Scribble marker on a plastic surface, pick it up with a damp brush | Watercolor paper, 140 lb | Soft wash, slightly darker at the edges |
| Tip to tip | Touch a dark marker’s tip to a light marker’s tip, then color | Smooth heavy cardstock | A dark-to-light fade inside a single stroke |
| Blender pen | Color dry, then pull the color outward with a colorless pen | Smooth heavy cardstock | Light fades with some visible strokes |
For a first image, the palette method is the most controllable of the three. Water evens out small differences in coloring, the brush reaches into tight corners better than a marker nib, and a mistake can be lifted with a dry corner of paper towel while it is still wet.
Tombow dual brush pens are the marker most crafters picture here, with a flexible brush on one end and a fine bullet tip on the other. Their colorless blender is sold in the same line as N00. Other brands of water-based brush pen behave much the same way.
Stamp with ink that ignores water
Water-based marker ink dissolves in water, and so does ordinary dye stamping ink. Run a damp brush across a dye-ink outline and the black line spreads into a gray halo around the whole image. Use an ink labeled waterproof and give it time to dry, or heat emboss the outline. Which ink families hold up under water is covered with the other stamp ink properties.
Dry coloring with no added water is gentler on the outline, but the marker’s own wet ink can still smudge a fresh dye-ink line. Waterproof ink costs nothing in flexibility, so it is the sensible default for every image you plan to color with these markers.
Palette blending, step by step
- Scribble the lightest shade onto an acrylic block in a small patch, and the darker shade in a second patch beside it.
- Squeeze the water brush until the bristles are wet but not dripping, then touch the tip to a paper towel once.
- Pick up the light color and cover the whole shape, keeping inside the stamped line.
- While the paper is still damp, pick up the dark color and touch it into the shadow side. It spreads into the wet area by itself.
- Squeeze water through the brush onto the towel until it runs clear before switching to the next color.
Keep the puddles small. A pool of water sitting at the edge of a petal dries into a hard, dark rim, and once dry it will not soften. If one forms, blot it immediately with the corner of a paper towel.
Leftover marker on the block reactivates later with a wet brush, so a palette of dried scribbles from one card can color the next.
Tip to tip without a brush
Hold the light marker brush-up and press the darker marker’s brush against it for a second or two. The light tip picks up a little dark ink. The next stroke on paper starts dark and fades to the light shade as the borrowed ink runs out.
This works best where each stroke follows one shape: a petal from base to tip, a leaf from vein to edge, the fold of a ribbon. On a large flat area the stroke pattern shows.
Afterwards, scribble the light marker on scrap until its own color comes back. Skipping this step is how a pale yellow marker slowly turns orange over a month of projects.
Blender pen on dry cardstock
The blender pen puts the least water on the paper of all three methods. Lay the darker shade along the shadow edge of a shape, then drag the colorless pen from inside that color out into the bare paper. It carries a little pigment along and leaves a short fade behind.
Wipe the blender tip on scrap after every pull, or it deposits the last color into the next area. The fade it makes is shorter and streakier than a palette wash, so it suits small shapes like berries, buttons and leaves better than a sky.
When the paper gives up
Smooth cardstock takes dry water-based marker well and very little water. After two or three damp passes over the same spot, the surface roughens, fibers roll up into pills, and the color turns blotchy where the paper is damaged. Nothing fixes it once that happens. Treat the panel as practice and move on.
Watercolor paper of 140 lb handles repeated water without breaking down. The smoother hot-press kind keeps the stamped detail sharper; cold-press has a texture that shows through the color. For a fully painted look with pans or ink pads, see watercoloring stamped images.
Getting more colors out of a small set
Water-based markers mix on the palette the way paint does. Yellow scribbled next to blue and pulled together with a damp brush makes green; a touch of the opposite color on the color wheel tones down anything too bright. A set of twelve markers covers far more than twelve colors this way.
That mixing is also what makes these markers efficient for batches. For a stack of handmade Christmas cards, choose two shades per element and mix every shadow on one palette, so all the cards in the set match. The coloring section compares this approach with alcohol markers and colored pencils.
Store dual brush markers lying flat. Standing on one end, the ink drains toward the lower nib and the upper one dries out.
Questions crafters ask
Why are little balls of paper forming where I color?
That is pilling: scrubbing a damp spot lifts the fibers. Make fewer, lighter passes, let each layer dry, and switch to watercolor paper whenever water is involved.
Can water-based and alcohol markers blend together?
Not into each other. The inks use different solvents and do not melt together, so keep each blended area to one kind of marker.
Is the color permanent once it has dried?
No. Water reactivates it, so a damp finger, a wet glue or a spritz lifts the color again. That is useful while blending and a hazard while assembling the card.
Do I need to clean the light marker after tip-to-tip blending?
Yes. Scribble it on scrap until the stroke runs back to its own color, or the next area you color starts out darker than planned.
More in Coloring Stamped Images: Marker, Pencil and Watercolor Techniques