Alcohol Markers on Stamped Images: Smooth Blends and the Right Paper
On the table
- Alcohol markers in 2-3 color families, three values each
- Colorless blender marker
- Smooth bright-white cardstock made for alcohol markers, 80-110 lb
- Black dye ink labeled safe for alcohol markers
- Light gray stamping ink for no-line coloring
- Scrap copy paper as a bleed-through sheet
- White gel pen, fine tip
Alcohol marker coloring fails in two predictable ways. Either the color dries in stripes, every stroke visible like a lawn after mowing, or the ink creeps past the stamped line into the white background. Both come from one property of the ink: the alcohol carries dye through the paper fibers and keeps spreading until it evaporates, which takes only a few seconds. Learn to work inside that window and most of the rest is choosing colors.
Alcohol markers are one of four media compared in the guide to coloring stamped images, and the one that rewards practice most visibly.
Paper that lets the ink move, then stop
The paper has to be smooth, dense and bright white. Smooth so the nib glides. Dense so the ink spreads sideways in a controlled way instead of sinking straight down. White because alcohol ink is transparent, and any cream or off-white base shows through as a yellow cast that dulls blues and purples.
Cardstock sold specifically for alcohol markers, usually in the 80 to 110 lb range, meets all three. Ordinary textured cardstock drinks the ink, needs far more of it to look even, and leaves the surface fuzzy.
Expect bleed-through on every paper. Keep a sheet of scrap copy paper under the panel and move the panel to a dry spot once the scrap is saturated, so the ink pooled underneath does not stain the back.
An outline the markers cannot dissolve
Standard dye ink lifts and smears under alcohol, and wet pigment ink smudges. Stamp with an ink sold as safe for alcohol markers and give it a few minutes before the first stroke. Laser-printed digital stamps are alcohol-proof too; inkjet prints usually are not. A comparison of dye, pigment and hybrid stamp inks sorts the ink types by what they will tolerate.
Heat embossing also works, with one catch. The raised line can deflect the nib and leave a pale halo along the edge, so color right up to the ridge with the very tip of the brush.
No-line coloring
A black outline gives any image a cartoon look. For a softer, painted result, stamp the image in light gray or in a pale ink close to the lightest marker in your plan, then color straight over the line. The faint outline vanishes into the color and the image reads as shapes instead of drawings.
It is harder than it looks. Without a dark edge to aim at, every slip past the boundary shows, so start with a simple leaf or flower before trying a face.
Reading the color families
Copic’s numbering is worth learning even with another brand, because many alcohol marker lines borrow its logic.
The letters name the family: B for blue, G for green, R for red, YR for yellow-red, E for earth tones, and C, N, T and W for cool, neutral, toner and warm grays. The first digit after the letters describes saturation, lower numbers being more vivid and higher ones grayer. The last digit gives the value, from 0 for the lightest to 9 for the darkest.
A blending group is three or four markers that share the letters and the first digit, with values a few steps apart. B21, B24 and B26 make a light-to-dark blue that melts together easily, since saturation holds steady and only the value changes. Pairing B21 with B97 is possible, but the grayer marker pulls the light blue dull where the two meet. When a store set leaves gaps, buy the missing middle value before buying a new color.
Blending, stroke by stroke
- Cover the whole shape with the lightest marker, using small overlapping circles, until the paper looks evenly damp.
- While that layer is still wet, add the middle value on the shadow side, across roughly two thirds of the shape.
- Put the darkest value only in the deepest shadow, as a narrow band.
- Go back over the dark-to-middle boundary with the middle marker, then over the middle-to-light boundary with the light one. Each pass pulls the colors into each other.
- If steps between values still show, run the light marker over the whole shape once more.
The flick stroke deserves an evening of its own. Press the brush nib down at the dark end and lift it off as you move toward the light, so the ink trails out to nothing. On scrap, fill a 1 inch square with flicks starting from one side. When that square fades evenly with no visible lines, the stroke is learned.
Skip the colorless blender as a blending tool. It is a marker full of clear alcohol, and over color it pushes dye outward and leaves a pale, sometimes blotchy patch. It is good for softening one hard edge or lightening an area that went too dark, and for little else.
Keeping the color inside the line
Bleeding past the outline happens when there is more ink on the paper than the fibers can hold. Near an edge, work toward the line with a light touch and stop just short of it; the ink covers the last small distance by itself. Dark markers bleed more readily because they go on heavier, so color dark areas that border white with especially low pressure.
When a slip does happen, a colored background can hide it. Mask the colored image, blend ink around it, and the stray color disappears into the new background. The guide to masking a stamped image shows how to cut a mask that fits.
A dry marker base also takes texture well. Fur, wood grain and fabric weave are easier added afterwards in pencil, as described in the colored pencil guide, since a marker brush nib cannot draw a crisp hair-thin line.
Nibs, refills and caps
Most alcohol markers are refillable and their nibs replaceable, so a frayed brush tip is a small repair and not a reason to buy a new marker. Push each cap on until it clicks. Alcohol escapes through a loose cap surprisingly fast, and a half-dried marker lays down pale, scratchy stripes that look exactly like poor technique.
Questions crafters ask
Why does my alcohol marker coloring look streaky?
Part of the layer dried before the next stroke overlapped it. Color one small section at a time, keep its edge wet, and go over the whole area once more with the same marker to even it out.
Can the colorless blender fix a slip past the line?
Partly. It pushes ink outward and lightens it, so it can pull a small slip back toward the outline, but it never returns the paper to clean white.
Do alcohol markers work on kraft or watercolor paper?
Poorly on both. Watercolor paper soaks the ink up and dulls it, and on kraft the transparent ink darkens and loses its hue.
How many markers do I need to start?
Three values in each family you use most, plus a colorless blender. A skin-tone group, a green, a red and a gray group cover most simple images.
Why did my black outline turn gray?
The marker dissolved the stamping ink. Restamp with an ink labeled for alcohol markers, or heat emboss the outline so there is nothing left to dissolve.
More in Coloring Stamped Images: Marker, Pencil and Watercolor Techniques