Watercoloring Stamped Images: Flat Paper, Ink and Water Brush Control
On the table
- Watercolor paper, 140 lb (300 gsm), hot-press or cold-press
- Waterproof black stamping ink, or embossing powder and a heat tool
- Water brushes, small and medium tips
- Pan watercolors, or Distress Ink pads used as paint
- Nonstick craft sheet as a palette
- Low-tack painter's tape
- Paper towels
- Stamp positioning tool
Watercolor gives a stamped image the softest color of any medium, and it also brings water, which is where the trouble starts. Water warps cardstock. It dissolves the wrong stamping ink, and it carries color anywhere the paper happens to be damp, including past the outline. Each of those problems has a fix, and all three fixes are decided before the first brush stroke.
Watercolor is the most unpredictable of the four media on the coloring hub, and also the one where a slightly loose result still looks deliberate.
Paper weight and surface
Watercolor paper is sold by weight, and 140 lb (300 gsm) is the usual choice for cards. It takes several washes without much buckling, cuts cleanly on a paper trimmer and sits flat on an A2 card front when trimmed to 4 x 5.25 inches. Lighter 90 lb paper ripples badly as soon as it gets wet. Heavy 300 lb paper stays flat under almost any amount of water but makes a thick, stiff card front.
The surface matters as much as the weight:
- Cold-press has a bumpy texture that holds water and gives washes a slightly grainy look. It suits loose florals and backgrounds.
- Hot-press is pressed smooth. Stamped detail prints more cleanly on it, which makes it the better pick for fine-line images.
Tape the panel to the desk or a board on all four sides with low-tack painter’s tape before painting. It dries much flatter that way, and peeling the tape off leaves a crisp white border that already looks like a mat.
Outlines that survive the water
Stamp with an ink labeled waterproof and let it dry completely. Ordinary dye ink turns into a gray smear the moment a wet brush crosses it, and there is no rescuing that panel.
Heat embossing is the more reliable route. Melted embossing powder is plastic, so water cannot dissolve it, and the raised ridge slows a wash at the line, which makes coloring right up to the edge easier. Black powder over clear embossing ink, or clear powder over black pigment ink, both work. Powders, anti-static prep and stray specks are covered under heat embossing an outline.
Textured paper often leaves gaps in a stamped line, especially with large solid areas. A stamp positioning tool holds the stamp in place so you can re-ink and stamp a second time on exactly the same spot.
Paint options for small panels
| Color source | How to use it | Worth knowing |
|---|---|---|
| Pan watercolors | Wet the pan, lift color with the brush | Widest color range, mixes cleanly |
| Distress Ink pads | Press the pad onto a craft sheet, pick up with a water brush | Uses colors already on the shelf; reactivates with water even after drying |
| Ink reinkers | Put one drop on the craft sheet | Very concentrated; dilute heavily |
| Water-based brush markers | Scribble onto the craft sheet | Works like palette blending with brush markers |
A nonstick craft sheet makes a good palette for all of these. Dried color on it reactivates with a wet brush, and the sheet wipes clean with a damp towel.
Distress Ink used as paint has a quirk worth knowing. It stays water-reactive after drying, so a finished area can be softened with a damp brush days later. The same property means wet glue or a stray drop of water will lift it again, so adhere a Distress-painted panel with tape or foam squares.
Saving the whites
Watercolor has no true white. Decide on the highlights before the first wash and leave them as bare paper: the top edge of a petal, a glint on a berry, the rim of a teacup. A dot of white gel pen added after drying can rescue a highlight that got painted over, though it always reads as a dot of ink on top of the color.
Handling a water brush
A water brush stores water in its barrel and feeds it to the bristles when you squeeze. Squeeze too hard and a drop lands on the panel. Too little, and the color drags and streaks.
Give the barrel one light squeeze, touch the tip to a paper towel, then pick up paint. To change colors, squeeze gently while stroking the tip across the towel until the water runs clear. A small tip handles petals and leaves; a medium tip covers a background on a 4 x 5.25 inch panel without too many refills.
For a larger background, a traditional round brush and a jar of water carry more water per stroke and leave fewer hard edges than a water brush.
Wet-on-dry, wet-on-wet, glazing and lifting
Wet-on-dry means painting onto dry paper. Edges stay where you put them, so use it for small shapes and anything that touches the stamped outline.
Wet-on-wet starts with a coat of clean water over the shape. Touch color into it and the pigment spreads into soft, unplanned gradients. Keep the water inside the outline, because the color follows the water wherever it goes.
Glazing builds depth in layers. Let one layer dry completely, then add a second transparent layer only on the shadow side. Each glaze deepens the one below it without lifting it, provided the first is truly dry.
Lifting takes color back out. Blot a still-wet area with a crumpled paper towel or a thirsty, dry brush to create a highlight on a petal or a cloud in a sky.
Not every color lifts equally. Some come back up almost completely, while others stain the paper on contact and barely move. Painting a test strip of each color on scrap and lifting half of it tells you which is which before it matters.
Drying without damage
A heat tool speeds drying, but held still and close it pushes wet paint toward the edge of the hot spot and can warp the paper further. Keep it moving, a few inches away, or simply let the panel dry flat on the desk.
Before removing the tape, rest the back of a finger on the painted area. If it still feels cool, it is still damp, and a damp panel curls the moment the tape comes off.
Questions crafters ask
Why does my stamped image look patchy on watercolor paper?
The paper's texture stops the stamp from touching every spot. Stamp twice in the same position with a positioning tool, or switch to hot-press paper, which is smoother.
Can I watercolor on regular cardstock?
Only with very little water. Cardstock warps, pills and takes color unevenly, so for anything beyond a light wash use watercolor paper.
How do I flatten a warped watercolor panel?
Let it dry completely, then press it under a stack of heavy books overnight. Taping the panel down before painting prevents most of the warping in the first place.
What are the cauliflower shapes in my wash?
Blooms. They form when wetter paint runs into an area that is already half dry. Work fully wet or wait until the area is bone dry before adding more.
More in Coloring Stamped Images: Marker, Pencil and Watercolor Techniques